Engine/Rotax

869 topics in this forum

1. Oil Flow Route

   By Roger Lee, December 1, 2010
   • 0 replies
   • 328 views
   • 
   • Roger Lee
   • December 1, 2010

2. Where does the oil come from

   By Roger Lee, December 1, 2010
   • 0 replies
   • 298 views
   • 
   • Roger Lee
   • December 1, 2010

3. I have a bad mag drop

   By Roger Lee, December 1, 2010
   • 0 replies
   • 317 views
   • 
   • Roger Lee
   • December 1, 2010

4. "Lubricate the exhaust manifolds-muffler ball joints...

   By FastEddieB, November 29, 2010
   • 3 replies
   • 1.4k views
   • 
   • hhobbit
   • November 30, 2010

5. RPM/Density Altitude/% Power

   By S3flyer, November 17, 2010
   • 7 replies
   • 1.1k views
   • 
   • 207WF
   • November 24, 2010

6. Do's and Don't for plugs and oil

   By Roger Lee, November 19, 2010
   • 6 replies
   • 861 views
   • 
   • S3flyer
   • November 20, 2010

7. BullyHawk Soft Start Install + ROTAX Questions

   By FastEddieB, November 13, 2010
   • 2 replies
   • 2.3k views
   • 
   • FastEddieB
   • November 13, 2010

8. 100LL vs. E10

   By Scotsman58, November 10, 2010
   • 9 replies
   • 1.1k views
   • 
   • airhound
   • November 12, 2010

9. Mind stimulating fun questions

   By Roger Lee, November 7, 2010
   • 12 replies
   • 1.7k views
   • 
   • Admin2
   • November 11, 2010

10. Embarrassing ROTAX Ignition Question

    By FastEddieB, October 22, 2010
    • 11 replies
    • 1.1k views
    • 
    • FastEddieB
    • November 4, 2010

11. Radiator tape

    By PDG, October 24, 2010
    • 18 replies
    • 1.6k views
    • 
    • airhound
    • October 29, 2010

12. Rotax "Line Maint" manual revisions

    By Roger Lee, October 20, 2010
    • 0 replies
    • 443 views
    • 
    • Roger Lee
    • October 20, 2010

13. Going beyond calendar year TBO

    By Roger Lee, October 18, 2010
    • 2 replies
    • 688 views
    • 
    • Roger Lee
    • October 20, 2010

14. Carb rebuild question

    By Roger Lee, September 3, 2010
    • 7 replies
    • 644 views
    • 
    • Runtoeat
    • October 18, 2010

15. Needle position

    By Angelitomon, October 13, 2010
    • 8 replies
    • 2.7k views
    • 
    • Angelitomon
    • October 16, 2010

16. Oil Pressure

    By Roger Lee, June 21, 2010
    • 13 replies
    • 3k views
    • 
    • Runtoeat
    • October 13, 2010

17. ROTAX 912 Voltage Regulator Failure Mode?

    By FastEddieB, October 10, 2010
    • 6 replies
    • 3.9k views
    • 
    • Roger Lee
    • October 13, 2010

18. 1200 mile trip finished! question about oil temps

    By kentuckynet, September 21, 2010
    • 13 replies
    • 825 views
    • 
    • Roger Lee
    • October 4, 2010

19. Fuel additive when using 100LL ???

    By kentuckynet, October 1, 2010
    • 2 replies
    • 6.2k views
    • 
    • kentuckynet
    • October 3, 2010

20. Oil Analysis

    By Roger Lee, June 23, 2010
    • 4 replies
    • 749 views
    • 
    • Roger Lee
    • September 17, 2010

21. Best Oils for Rotax 912S in the US

    By wlfpckrs, September 15, 2010
    • 8 replies
    • 3.4k views
    • 
    • Roger Lee
    • September 17, 2010

22. Read that Plug

    By Roger Lee, September 10, 2010
    • 0 replies
    • 506 views
    • 
    • Roger Lee
    • September 10, 2010

23. Maximum performance 912

    By markmn, August 2, 2010
    • 6 replies
    • 615 views
    • 
    • Roger Lee
    • August 14, 2010

24. Carb balance

    By Roger Lee, June 20, 2010
    • 2 replies
    • 768 views
    • 
    • Roger Lee
    • August 10, 2010

25. Oil Pressure sender remote mount

    By Roger Lee, August 8, 2010
    • 0 replies
    • 1.4k views
    • 
    • Roger Lee
    • August 8, 2010