sandpiper Posted July 5, 2010 Report Posted July 5, 2010 In January I decided to order new fuel sight tubes from FD. I knew I would pay a little more than if I went to the local auto parts store but figured it wouldn't be that much more, they would have the markings on them, be cut to length, etc. This was a back order item but I wasn't concerned because I wouldn't need them until August when my annual is due and I will pull the wings. The package arrived about a month ago but I didn't open it until yesterday as I had been gone for awhile. The tube was not cut to length, just a single 15" piece. No big deal, even a caveman can handle a cut to length. Other than "made in Germeny" the tube isn't marked either but, that's OK. Probably better to mark them myself during an incremental known fill. So far so good. Then I dig out the invoice and find this cost me , are you sitting down because I should have been, $19.60 USD per foot!!! No, I didn't hit the wrong keys and your glasses are fine. $11.86 for a bucks worth of tube and $12.64 to send it UPS. It could have been sent U.S. Mail for 10% of that! Now, if this was a special material that would never darken with age when using the recommended mogas, that would still be OK. But, from what I've seen on this forum, it, too, will turn dark in about a year. Now, I should have asked at order time, how much will this cost? But, I didn't because who would have thought anyone would have the nerve to ask $24.50 for a bucks worth of tube? Bottom line, it's my fault. I didn't ask. But, FD could have and should have said 'just go to your local auto parts store." They didn't. Buyer beware. Fool me once, shame on you. Fool me twice, shame on me. Still a great airplane and a great company. This just got my knickers in a knot and I had to get it off my chest!!
acresflyer Posted July 6, 2010 Report Posted July 6, 2010 Sandpiper, If the tubes say " REHAU RAUCLAIR -E527 8/2 8x12 Made in Germany 0220/B",I would not install them. Lockwood put a set on my CTSW and they became cloudy and unreadable in less than 2 weeks.
josjonkers Posted July 6, 2010 Report Posted July 6, 2010 John, with all due respect, I am not sure what else you could conceivably expect. Stocking, warehousing,handling, packaging and shipping from Germany?? This is not North America! Let's say, it was a 10 minute job to do the whole order, shipping for $12 seems cheap and the material including the time spent another $13? I would say that it is reasonable giving that they went through the whole order. Just my opinion.......... Cheers, Jos
sandpiper Posted July 6, 2010 Author Report Posted July 6, 2010 Acresflyer, That is exactly what is on the tube. Oh, well, lesson learned.
Flying Bozo Posted September 11, 2011 Report Posted September 11, 2011 I realize that some time has gone by since the last post on the sight gauges but I have a slightly different issue with them. Maybe someone could shed some light on the issue of the fuel quantity stickers that are right next to the sight gauges. It appears that both of my gauge stickers are on too low making it appear that there is more fuel in the tank that actually is there by about 2 gallons on each side. When my tank read 3 gallons I drained from the sump and only got one gallon out ( the one tank was dry so everything that I got out was from the tank that read 3 gallons. Is there a template that accurately locates the stickers that show the fuel quantity? I think the 1 gallon marker should be right at the bottom of the sight gauge but my one gallon marker is below the bottom of the lower fitting on the sight gauge, any comments or better ideas? Larry Minch Cottonwood, AZ
Runtoeat Posted September 11, 2011 Report Posted September 11, 2011 Hi Larry. During the 5 year rubber replacement I decided to really figure out how much fuel remained in my tanks while I had my wings off and all fuel removed. When I re-installed each wing, I started with the left wing, filled this up wiith 3 gallons of fuel and then opened the gascolator until I saw fuel flowing. At this point, I used a paint pencil and marked the sight tube with a line that tells me that there is "3 gallons remaining". Before going to the right wing, I drained the left wing until the fuel could barely be seen at the bottom nipple for the sight tube. I opened the gascolator and timed how long it took for all the fuel remaining to be drained. It took about 15 minutes for this. As the fuel in the wing diminished, I noticed that the flow also diminished due to the reduction in pressure. Still, the flow was above the FD minimum all thru the final drainage. I was surprised by the amount of fuel remaining in the tubes running down the pillars but then I read somewhere in Flight Design literature that the fuel tubes in this area are oversized to act as reservoirs to hold adequate fuel to supply the engine even when the fuel pickups in the wings might be left dry by banking during landing with very little fuel remaining. By measuring the fuel in this manner, I won't get so anxious when I see the fuel rising and lowering and bumping the bottom nipple in my sight tubes, knowing that adequate fuel remains in the pillars to supply the engine during the periodic low excursions of the fuel. I will also know the point where there is an accurate 3 gallons of fuel remaining (6 total), which is my minimum and means I'm landing at the nearest airport. Note: I realize that this method still leaves variance in the measurement of fuel in the system since the fuel tanks are not isolated totally due to them being linked by the "T" fitting which allows fuel to fill up the opposite pillar. By marking the sight tubes where I have 6 gallons fuel remaining onboard, I feel that I have enough reserve left to safely get back on the ground and find fuel.
Flying Bozo Posted September 11, 2011 Report Posted September 11, 2011 HI Runtoeat, Thanks for the commentary on the fuel quantity and flow. My issue is a little different although if I had marked the sight tubes as you did that would solve the problem. On the ground sitting absolutely still and level if each tank reads 3 gallons according to the sticker there is actually only one gallon per tank. That is all I can drain out of the bottom of the fuel gasgalator. So it looks like 6 gallons total but in reality there are only two gallons. I think the stickers that are on my SW are positioned too low by about 2 gallons each. That is why I was wondering if there was a template that got the stickers in the proper position. So my solution is to remove the stickers and place them about 3/8 of an inch higher so that when it is critical to know what is left in the tank I won't think there is 3 gallons per side when there is only 1 gallon per side. Your method of marking the sight gauge is the best solution but I will move the stickers too. Larry Minch Flying Bozo Cottonwood, AZ
Rogerck Posted October 19, 2012 Report Posted October 19, 2012 I'm having the fuel sight tubes replaced in the near future. Is there any update on a new/better tubing to use or is it best to just purchase from FD? Roger Kuhn
Tip Posted October 19, 2012 Report Posted October 19, 2012 Call Arian at FDUSA and ask for the stiff sight tubes that he forms. My friend's SW has had them on for over 2 years and they are crystal clear. Mine have been on for 18 months and they are perfect.
207WF Posted October 19, 2012 Report Posted October 19, 2012 I wouldn't worry about the location of the stickers. I mark the sight tubes directly with a black permanent marker when refilling the tanks after the tubes are replaced. I pick a couple of strategic fuel levels. Last time I used 4 and 9 gallons per side. Then, I mark the stickers at the 4 and 9 gallon indications to remind me what the marks on the sight tubes mean. I find that if I interpolate between the two marks on the sight tubes, I get accurate figures between the two fuel levels. WF
Rogerck Posted October 26, 2012 Report Posted October 26, 2012 Update. I called FD and the currently approved fuel sight tube material is Tygon fuel tubing, which is tinted pale yellow for identification. I was told that this material provides good transparency in spite of the tint. I ordered some from Lockwood. FD no longer offers the harder material suggested by Tip. Roger Kuhn
Rogerck Posted October 27, 2012 Report Posted October 27, 2012 I haven't found a single person that likes the yellowed Tygon tubing. It's hard to see the levels and it gets worse over time. What do you suggest? Roger Kuhn
Tom Baker Posted October 27, 2012 Report Posted October 27, 2012 The Tygon that Flight Design has now is clear, not yellow tinted.
Runtoeat Posted October 27, 2012 Report Posted October 27, 2012 I used to use Tygon for my work. Recall the stuff I used was clear. I note that Grainger sells 3/8" ID clear Tygon in minimum 50' length. A few people buying 2 or 3 foot lengths off of the 50' would use this up fast.
Rogerck Posted October 27, 2012 Report Posted October 27, 2012 The Tygon formulated for gasoline is tinted yellow. See http://www.hoseline.net/hose/fgpvc.htm I'm not sure clear Tygon has the same resistance for gas with ethanol. Having had a bad experience with deteriorating new fuel hose on the five year rubber change, I'm wary of anything not specifically formulated for gas. On the other hand, maybe the clear tygon is just fine. Roger Lee, where do you get the clear poly you're using? Is this just hardware store stuff? Roger Kuhn
Tom Baker Posted October 27, 2012 Report Posted October 27, 2012 I looked on a piece of tubing and it is Tygothane C-210-A. I looked this up and it says it is for fuels along with other applications.
Rogerck Posted October 27, 2012 Report Posted October 27, 2012 Here is the clear poly tubing I'm going to try. http://www.amazon.com/gp/product/B000FMUYVS/ref=oh_details_o00_s00_i00 NSF-61 polyurethane specs indicate it's ok to use with fuel. See the Poduct Description. Roger Kuhn
floats Posted November 12, 2012 Report Posted November 12, 2012 My tube gage split after one year ( I replace them every year)of use and the fuel leaked on the plane door and cabin. I could not find a product that would take the stain out. Any suggestion.
sandpiper Posted November 12, 2012 Author Report Posted November 12, 2012 A product called Haze Glaze from www.composiclean.com works on most problems I have encountered including fuel stain on the wings from full tanks.
Rogerck Posted November 12, 2012 Report Posted November 12, 2012 On post #20, I mentioned trying NSF-61 polyurethane. I purchased some and it will not work. It's a stiffer tubing and will kink with the small turn radious required on the CT sight guage. I've gone with Roger Lee's suggestion and installed hardware store poly tubing. Roger Kuhn
Runtoeat Posted November 12, 2012 Report Posted November 12, 2012 Floats, I use plain rubbing alcohol to remove fuel stains on my wings and to remove exhaust stains on the underneath. This has been very effective yet it does not seem to harm the exterior finish. If your surface is oxidized as Roger has indicated, not sure if the fuel has gotten into the paint and might cause a lasting stain? For your windows, Micro Mesh makes a polishing creme and also Meguiars makes a very fine polishing product which I use on the clear side windows and windshield called PlastX
GlennM Posted November 18, 2012 Report Posted November 18, 2012 My exhaust and fuel stains come off with Nu Finish.
Recommended Posts
Archived
This topic is now archived and is closed to further replies.